How To Remove FRP Lock on Samsung J1 2016 (SM-J120H)

16:22:00 12 Comments A+ a-

Below is the Instruction you should do to remove FRP lock on your Samsung J1  (SM-J120H).

Pre-Requisites:

Odin
SM-J120h frp reset

After Downloading above files,Extract it in your Desktop

Now,Put Phone Download Mode

  • Turn off the device     
  • Press and hold Volume Down key + Home Key, while pressing these keys then press and hold Power key for a while     
  • Release all key when you see ODIN Mode / Download Mode
  • When connected successfully, you will get a message in Odin saying Added!!. (In case you don’t get it, try another USB port. If that doesn’t help either, then re-install USB drivers).
In Odin make sure that the Auto Reboot and F. Reset Time check boxes are the only options checked and nothing else is.

Click on PDA on Odin, locate the sm_j120h_convert_to_j120f_frp_reset_by_renz.tar.md5 file and hit the Start button to initiate the update process.

When flashing update installation is successfully completed, on Odin ID:COM will turn green and Odin will show you a PASS message.



After finish flashing on ODIN,Open Z3X Samsung ToolPRO v25.7

Select [J120F]

Put Again In DOWNLOAD MODE

Connect your Phone to PC

Press Reset FRP/React/EE and wait until Done

Follow on Phone screen to continue using phone....


All the Credits goes to Renz Altajeros for the FRP file!!!



12 comments

Write comments
Unknown
AUTHOR
10 December 2016 at 17:24 delete

big thanx sir your method is 100% work thanx again.and keep it up

Reply
avatar
Sir Georgie
AUTHOR
23 January 2017 at 19:00 delete

Thanx big tym your solution WORKED 100%. THANKS

Reply
avatar
Unknown
AUTHOR
10 March 2017 at 17:39 delete

i cant find z3x toolpro sir.. where i can download it?

Reply
avatar
17 March 2017 at 12:31 delete

where can i found the sm_j120h_convert_to_j120f_frp_reset_by_renz.tar.md5??

Reply
avatar
ansary
AUTHOR
18 March 2017 at 12:51 delete

The download is below pre-requisites

Reply
avatar
Unknown
AUTHOR
15 April 2017 at 22:45 delete

where to download z3x Samsung toolpro?

Reply
avatar
Anonymous
AUTHOR
16 April 2017 at 08:20 delete

not a free software

Reply
avatar
Unknown
AUTHOR
22 May 2017 at 17:06 delete

txnzzzz...bro.....ok pas alwrite

Reply
avatar
Unknown
AUTHOR
8 September 2017 at 12:19 delete

THANK YOU MR. REGARDS

Reply
avatar
Anonymous
AUTHOR
28 October 2017 at 12:29 delete

i am using j1(6).

After i pressed the start button in Odin , it display 'RESET' instead of 'PASS' .

I don't know what to do NEXT .


Reply
avatar
Anonymous
AUTHOR
28 October 2017 at 12:41 delete

Below is the message from ODIN

Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
sm_j120h_convert_to_j120f_frp_reset_by_renz.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:8)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
sboot.bin
NAND Write Start!!
RQT_CLOSE !!
RES OK !!
Removed!!

Reply
avatar
25 November 2017 at 10:10 delete

Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
sm_j120h_convert_to_j120f_frp_reset_by_renz.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
sm_j120h_convert_to_j120f_frp_reset_by_renz.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)
All threads completed. (succeed 0 / failed 0)

thus this says it did not work?!

Reply
avatar